游艇会206最新官方网站-游艇会线路检测中心

 欢迎访问游艇会206最新官方网站网站!

专注生产工业用清洗设备

让工业清洗无难事

电话

业务咨询电话:

18663767799

你所在位置: 首页-新闻动态-新闻资讯-超声波清洗设备的正确操作程序
新闻资讯

超声波清洗设备的正确操作程序

作者:guanli来源:/时间:2022-05-30

当你购买超声波清洗机时,你应该仔细学习超声波清洗机的说明书,请妥善保管,以备将来使用。现在我们来谈谈超声波清洗机的操作程序。
When you buy an ultrasonic cleaner, you should carefully study the manual of the ultrasonic cleaner. Please keep it properly for future use. Now let's talk about the operation procedure of the ultrasonic cleaning machine.
超声波清洗机的电源线一般与清洗槽分开。,将超声波电源与清洗槽连接。带排水管的超声波清洗机可以连接排水管并使排水管朝向排水处。
The power line of the ultrasonic cleaning machine is generally separated from the cleaning tank., Connect the ultrasonic power supply to the cleaning tank. The ultrasonic cleaning machine with drainage pipe can connect the drainage pipe and make the drainage pipe face the drainage place.
向清洗槽中加入适量的清水。液位应能淹没清洗后的零件,并低于高水位。有些型号有溢流管,因此应提前连接溢流管。
Add an appropriate amount of clean water to the cleaning tank. The liquid level shall be able to submerge the cleaned parts and be lower than the high water level. Some models have overflow pipe, so the overflow pipe should be connected in advance.
启动电加热开关,将水温调节到合适的温度(一般在50℃-60℃之间)。清洗机里有一个温度检测器。加热装置将继续加热至规定温度,然后进入保温模式。当温度低于一定值时,加热装置将自动启动并加热至设定温度。
Start the electric heating switch and adjust the water temperature to the appropriate temperature (generally between 50 ℃ -60 ℃). There is a temperature detector in the washing machine. The heating device will continue to heat to the specified temperature, and then enter the insulation mode. When the temperature is lower than a certain value, the heating device will automatically start and heat to the set temperature.
当水温升至30℃左右时,可根据产品工艺向清洗槽中加入零件清洗剂,比例为1:20或1:30。搅拌干净的水,使清洗剂完全溶解在水中。
When the water temperature rises to about 30 ℃, the part cleaning agent can be added to the cleaning tank according to the product process, and the proportion is 1:20 or 1:30. Stir the clean water to completely dissolve the detergent in the water.
使用超声波清洗机清洗某些油渍较重的零件时,可在清洗前提前刮去较厚的油泥或较厚的粉尘。简单的超声波清洗预处理将大大提高超声波清洗效率,缩短超声波清洗时间,延长超声波清洗机的使用寿命。
When using ultrasonic cleaning machine to clean some parts with heavy oil stains, the thicker sludge or dust can be scraped off in advance before cleaning. Simple ultrasonic cleaning pretreatment will greatly improve the efficiency of ultrasonic cleaning, shorten the ultrasonic cleaning time and prolong the service life of the ultrasonic cleaning machine.
超声波清洗设备
将零件放入不锈钢清洗篮中,轻轻放入清洗槽中。建议不要一次放置太多零件。尽可能均匀地摊铺,不要放得太紧。
Put the parts into the stainless steel cleaning basket and gently into the cleaning tank. It is recommended not to place too many parts at once. Pave as evenly as possible without placing too tightly.
打开超声波发生器电源,开始正常清洁工作。如有必要,顺时针转动功率调节旋钮以调节适当的功率。电流表显示正常电流为4-5安培。
Turn on the power supply of the ultrasonic generator and start the normal cleaning work. If necessary, turn the power adjustment knob clockwise to adjust the appropriate power. The ammeter shows a normal current of 4-5 amps.
超声波清洗的工作时间可根据零件状况确定。如果您在超声波清洗过程中感觉清洗几乎完成,可以先将电源旋钮调整到小,然后按下超声波工作按钮。通常,您可以直接关闭超声波电源。
The working time of ultrasonic cleaning can be determined according to the condition of parts. If you feel that the cleaning is almost completed during the ultrasonic cleaning process, you can first adjust the power knob to small, and then press the ultrasonic work button. Usually, you can turn off the ultrasonic power directly.
直接取出清洗篮,用清水冲洗干净的零件。之后,将零部件放入风扇或空气干燥器中进行空气干燥,直到它们在间隙通道中完全干燥。一些用户直接使用双槽或三槽清洗机,一槽用于超声波清洗,二槽用于水漂洗,三槽用于热风烘干,这样就省去了到处移动工件的麻烦。
Take out the cleaning basket directly and wash the cleaned parts with clean water. After that, put the parts into a fan or air dryer for air drying until they are completely dried in the clearance channel. Some users directly use double or three tank cleaning machines. One tank is used for ultrasonic cleaning, two tanks are used for water rinsing, and three tanks are used for hot air drying, which saves the trouble of moving workpieces everywhere.
超声波清洗设备用于清洗许多零件时,清洗液中的油泥含量非常高。再加上超声波的乳化作用,清洗液会变得浑浊。这样不仅使二次污染零件,而且可以削弱超声波的空化作用。此时,不应再使用含有清洗剂的液体。
When the ultrasonic cleaning machine is used to clean many parts, the oil sludge content in the cleaning solution is very high. Coupled with the emulsification of ultrasonic, the cleaning fluid will become turbid. In this way, not only the parts are polluted twice, but also the cavitation effect of ultrasonic wave can be weakened. At this time, the liquid containing cleaning agent should not be used.
超声波清洗设备的正确操作程序价相关内容具打这里了,您如果有什么想法的话欢迎关注我们www.jnthcsb.com
The correct operation procedures of ultrasonic cleaning equipment are listed here. If you have any ideas, please follow us at www.jnthcsb Com!
Baidu
sogou